iecutool

Automotive ECU Tools

iecutool

Automotive ECU Tools

عناوین یادداشت‌ها

  • XirDecoder Update: View Live ECU Tuning Modifications سه‌شنبه 2 دی 1404 10:52
    With the upcoming update, XirDecoder chip tuning software is introducing several important improvements. Previously, users would only receive a warning on the tuning page indicating that a file was not original. With the new update, after a file is uploaded on the main page, a new report screen will be available where...
  • Alientech KESS3 Update OBD Programming for Ford SID213 سه‌شنبه 2 دی 1404 10:51
    Alientech KESS3 released new OBD protocol for Continental SID213 ECU. 2.12.2025 — UPGRADE 2.74 A new KESS3 release that introduces OBD reprogramming for Continental SID213 ECUs on the latest diesel commercial vehicles and pick-ups, equipped with 2.0 EcoBlue engines (from 2022 onwards). No ECU removal Direct access via...
  • FormulaFlash 1.0.9.0 Release Adds New SIM2K and E-Series ECUs سه‌شنبه 2 دی 1404 10:48
    FormulaFlash ECU TCU programmer software released to V1.0.9.0 on Dec. 18th, 2025. READ-WRITE PROTOCOL BYD BYD TB10 R5F72531 BOSCH BOSCH M7.9.7.1-ST10F275 ST10F275 Boot mode reading EEPROM+FLASH Chang’an CHANGAN VISTEON STC-113-ST10F273 ST10F273 DEPHI LANDWIND DELPHI X7 MT62.1 SPC5643 GWM DELPHI MT95.1(MASTER) TC367...
  • Autotuner OBD VR Update for Porsche SDI10.x ECUs دوشنبه 1 دی 1404 11:13
    Get ready to tune the best of Stuttgart directly via the diagnostic port! Autotuner is thrilled to announce the release of the complete Porsche SDI10.x family on your Tool. You can now work on Porsche Macan, Cayenne, and Panamera equipped with SDI10.1, SDI10.2, SDI10.3, and SDI10.4 ECUs. Method: These protocols are...
  • Fix Foxflash No VR File for Crafter 2021 DCM6.2V دوشنبه 1 دی 1404 11:11
    Problem: VW Crafter 2021 dcm6.2v no go with foxflash . Virtual read obd2 not in database. Solution: On some models virtual file was not in database and solution on this is to upgrade or downgrade software version. Done it by ODIS Engineering software. Or read it in boot mode with other programmers.
  • Reading Dacia Duster 2021 MD1CS016 ECU With KESS3 دوشنبه 1 دی 1404 11:09
    Dacia Duster 2021. Flex cannot read, kess3 yes. Bosch MD1CS016 ECU. Read micro = 16mb.
  • AutoTuner Update Supports KTM KTKS and KTKZ ECUs پنج‌شنبه 27 آذر 1404 06:52
    You seemed to love the addition of the first KTMs to AutoTuner , so we decided not to stop there! Starting now, you can benefit from the KTM KTKS/KTKZ OBD NR protocol on your Tool. As a reminder, NR stands for " Normal Read" . This gives you access to the real content of the ECU on 14 different models from...
  • Foxflash Boot Mode Clone for Peugeot SID807EVO ECU پنج‌شنبه 27 آذر 1404 06:51
    Foxflash report today: Clone PEUGEOT PARTNER SID807EVO ECU successfully. SID807EVO Read/Write BOOT MODE Cloning ok Checksum correction by foxflash. NOTE: No need to read password for PSA SID807EVO, only read and write. If it is Ford SID807EVO, we need to read password first. Some users also reported that the PADFlash...
  • Flex Programmer Guide for Volvo DENSO MB279700 ECU پنج‌شنبه 27 آذر 1404 06:49
    Problem: It’s a Volvo XC-60 with DENSO MB279700–96xx ECU. Original ecu has been flooded with water. Have read eprom on bench no problem same as whole ecu. MMS Flex says there is no clone. How to clone this ECU with Flex programmer? Feedback and solution: It turned out that after writing full backup in to the...
  • Renault SID307 OBD Issue Fix Using Flex Boot Mode سه‌شنبه 25 آذر 1404 11:31
    Alientech KESS3 released new OBD & OBD VR protocols for Marelli MM11MPHW002 ECUs- Aprilia and Moto Guzzi motorcycles. Unlock tuning on the latest supersport and modern classic platforms from the Piaggio group with KESS3 — including the full RS and Tuono lineup and the Moto Guzzi V7 — and expand your offer across...
  • Alientech KESS3 Adds MM11MPHW002 ECUs for Motorcycles سه‌شنبه 25 آذر 1404 11:30
    I just had an issue with this ECU while trying to perform a Full OBD read Renault SID307 with Flex programmer . At the moment of connection, Flex managed to read the password, and right after that it started patching the ECU. A few seconds later, the cooling fan turned on, and shortly after, during the connection...
  • OBDSTAR DC706 Boot Mode Solution for GPEC2 ECM سه‌شنبه 25 آذر 1404 11:28
    How to read and clone the GPEC2 module? This module is used in Jeep, Chrysler, Dodge, and other American CDI vehicles. We will perform the process using the OBDStart DC706 ecu tool along with its MP001 adapter cable. Step-by-Step Process: Connection Setup First, we connect to the vehicle via OBD. Then, we navigate...
  • Autotuner Solution for Mercedes CRD3PLUS.A0 ECU Reading چهارشنبه 19 آذر 1404 10:06
    2015 Mercedes- C220D Delphi CRD3PLUS.A0 TC1797 ECU reading and writing review: Flex could not read/connect via Bench or even OBD- Tried both pinots, Tried TC1793 etc. Pulled out Foxflash with the same result. In the end completed with Autotuner worked first time. Very Strange as have done many of these before and...
  • Flex OBD Write Fail on VAG DCM6.2V ECU Fix چهارشنبه 19 آذر 1404 10:04
    Problem: Read and write DCM6.2V Vag ECU with MMS Flex programmer. At 29% the write failed and car didn’t start, voltage was 13.3. Any solution? Solution: Do these without a charger. Probably an internet or server issue. Or do it in bootmode! OBD after 21 with flex maybe can damage eeprom. Never had an issue but...
  • How to Solve Foxflash Update Server Connection Error چهارشنبه 19 آذر 1404 09:57
    Problem: Cannot get Foxflash working today. Error: There is a problem reaching the update server. Solution: so here’s the quickfix from one of our users FOR THE UPDATE SERVER ERROR! Download link and unzip to foxflash folder, then make a shortcut on desktop of the foxflash software. [https://files.fm/u/cn4dk6m6jz] Be...
  • How to Fix Foxflash Simos 18.1 Password Read Failure دوشنبه 17 آذر 1404 09:50
    Problem: Tried to read and write Simos 18.1 ECU with Foxflash but extract password not working. Solution: Voltage is not good. User feedback: Solved! Had a problem with the resistances, the voltage is true, the power supply died and did it with the standard. READ OK. WRITE OK. CHEKSUM OK FOXFLASH. STAGE 1 + POPS VW...
  • KESS3 Adds EVPT VCU3000 Boot Mode for EVs دوشنبه 17 آذر 1404 09:48
    Alientech KESS3 released a new protocol for EVPT VCU3000- Citroen, Fiat, Opel/Vauxhall. Take the next step in EV tuning: work in BOOT mode on the latest EVPT VCU3000 units, now supported on ultra-compact electric vehicles equipped with 5.5 kWh systems from 2025 . Full read and write access in BOOT mode Direct...
  • Foxflash Boot Read Write Skoda Simos 3PG ECU Guide دوشنبه 17 آذر 1404 09:46
    Read and write Skoda Fabia 1.2 12V Siemens Simos 3PG ECU with Foxflash successfully. Lambda OFF. BOOT Read 2min. BOOT Write 4min. Checksum by Lsuite. FoxFlash does not correct the checksum for this type driver. Only self do with other software like Lsuite.
  • New ECUs Added in FormulaFlash Version 1.0.8.0 Update سه‌شنبه 11 آذر 1404 10:17
    FormulaFlash ECU TCU programmer released new software version 1.0.8.0 on December 1st, 2025. V1.0.8.0 Adds following ECU types: Volvo EDC15C11–3.XNO1 EDC15C11–4.X250KNO1 EDC15C11–4.X500KNO1 EDC15C11–3.XNO2 EDC15C11–4.X250KNO2 EDC15C11–4.X 500K NO2 EDC15C3 KLINE NO1 EDC15C3 KLINE NO2 EDC15C7 KLINE Opel ME1.55 KLINE...
  • How to Use OBDSTAR G3 for Peugeot DCM6.2C DTC Off سه‌شنبه 11 آذر 1404 10:16
    OBDSTAR X300 Classic G3 worked very well today, had to do DTC off on a Peugeot boxer dcm6.2c. ECU type: DCM6.2C Mode: Boot mode. Read ext eeprom and int flash ok. Write eeprom and flash ok. Only had DCM6.2A listed but I know the pin out is the same. Worked great with fast read and write and even did the checksum...
  • Foxflash No Red Light Problem in Bench Mode Solution سه‌شنبه 11 آذر 1404 10:11
    Problem: No red light on Foxflash programmer bench box and switch, has happened to anyone? Solution: Light comes only when tool start reading, when it says keep ecu power on make sure switch is at 1, then press ok that’s when the light will come Power will only come on in bench mode after the program prompts you to...
  • How to Repair VW DCM6.2V No Start Issue on Foxflash پنج‌شنبه 6 آذر 1404 10:02
    Problem: How do I read and write down a driver in a vw dcm6.2v with foxflash in boot mode, because after installing stage 1 (via OBD) the car does not start and I can’t bet anything? Solution: That situation usually comes from checksum handling or wrong patch area — DCM6.2V is picky. If you can still read and connect...
  • Foxflash BDM Guide for SSANGYONG Delphi DCM3.2AP ECU پنج‌شنبه 6 آذر 1404 10:00
    It’s a SSANGYONG ACTYON 2009, 2.0, 104kW. ECU type: Delphi DCM3.2AP Tool used: Foxflash Mode: BDM mode. BDM MPC 55x/56x full backup with foxflash. Checksum correction by foxflash, IMMO OFF ok. ST95320 eeprom write back with TL866II programmer for set write protect.
  • KESS3 Upgrade V2.65: Adds Ford MG1 MD1 OBD Support پنج‌شنبه 6 آذر 1404 09:55
    The protocols you were waiting for are now finally active on Alientech KESS3 . 24.11.2025 — UPGRADE 2.65 Ford’s evolution continues through increasingly efficient powertrains, new electronic management systems, and Bosch platforms designed to enhance performance and safety. With this update, KESS3 takes a decisive...
  • How to Read Maserati BCM BSI MC9S12DG256 with Multi Prog سه‌شنبه 4 آذر 1404 09:51
    Read and write the Maserati BCM/BSI module with Xhorse multi prog successfully. MASERATI BCM Type: Magneti Marelli BSI Processor: MC9S12DG256 unsecured Read mcu, eeprom and flash successfully on bench mode. vvdi prog will also read this BCM.
  • KESS3 Adds Boot Support for Landini McCormick CompAir سه‌شنبه 4 آذر 1404 09:49
    Alientech KESS3 released new protocol fpr HJS ACU- CompAir, Landini, McCormick. Operate in BOOT mode on next-generation agricultural and industrial machines, expanding your service options on some of the most requested work vehicles in the field. Read and write in BOOT mode on the HJS ACU control unit Work with...
  • Foxflash guide to boot-read and clone Renault SID306 چهارشنبه 28 آبان 1404 11:15
    Renault SID306 ECU cloning is done with Foxflash programmer. Continental Sid306 Infineon TriCore SAK-TC1766 boot mode clone ecu. Need attention for pinout because very small in ecu pin. Cloning cannot be done on bench. Read in boot ok. Write in boot ok. Checksum by foxflash. Better keep power supply 12V+.
  • KESS3 update for MAN PTM5 ECU boot read and write چهارشنبه 28 آبان 1404 11:13
    Alientech KESS3 released new protocol for Continental PTM5- MAN 12.4L trucks. Operate in BOOT mode on European heavy-duty vehicles thanks to the latest update dedicated to MAN engines. Read and write the ECU in BOOT mode. Work safely on 12.4L engines across the most reliable MAN series. Improve efficiency and overall...
  • How to use OBDSTAR DC706 for VW Up ME17.5.24 ECU work چهارشنبه 28 آبان 1404 11:11
    OBDSTAR DC706 read and write VW up with ME17.5.24 ecu, start breaker remove. Read eeprom & flash ok. Write eeprom and flash ok. Checksum by DC706. DC706 will also read immo data, decrypt immo data, write VIN and IMMO OFF for this ECU. Did a few already for VW and Audi, worked great. mp001 is not necessary, the...
  • How to solve Flex missing SN and firmware information دوشنبه 26 آبان 1404 09:56
    Problem: What’s going on with the Magic Motorsport Flex programmer? Cannot see device SN, no connection. Solution: Possible solutions: There is no usb connection. Change cable or port. Reinstall new software from mms and it will be fixed Go to your mms page and download it and see how it works Go to the help desk and...