iecutool

Automotive ECU Tools

iecutool

Automotive ECU Tools

عناوین یادداشت‌ها

  • CG FC200 Guide to Porsche SDI6 SDI7 CS PIN Reading دوشنبه 20 بهمن 1404 12:18
    As titled, iecutool.eu here will show how to read Porsche SDI6/SDI7 engine ECU CS and PIN code using CG FC200 programmer. In FC200 software, select Porsche SDI7 ECU. Check bench wiring diagram. Connect ECU with FC200 follow the diagram. Read and save ExtEEPROM and Pflash data. Select decrypt immo data. Then load...
  • ECM Titanium MD1CP061 Update for Ford Ranger and Amarok دوشنبه 20 بهمن 1404 12:16
    Alientech ECM Titanium released new driver update- Bosch MD1CP061 for Ford Tanger, Volkswagen Amarok and more. Targeted control for modern high-performance diesel pickup trucks with ECM Titanium. Dedicated calibration for Bosch MD1CP061 ECUs on latest-generation commercial vehicles. Advanced management of EGR...
  • Flex vs KESS3: Reading Renault SID321 ECU دوشنبه 20 بهمن 1404 12:14
    Renault Continental SID321 reading review: MMS Flex failed to read SID321 via OBD VR. It says no Virtual read available for this software version on the server. Cannot do it on bench when no vr on server. Did it with Alientech KESS3 . Autotuner will also do this ECU. AT is the best in this ecu.
  • Alientech KESS3 Update GM ACDelco E84 ECM on Bench Mode پنج‌شنبه 16 بهمن 1404 10:35
    Alientech KESS3 developped bench protocol for AC Delco E84- GM compact platforms. Expand your workshop operations with this new development providing direct ECU access — simplifying procedures on compact vehicles and improving workflow efficiency. Read and write on AC Delco E84 in BENCH mode Direct ECU access for...
  • Flex ECU Programmer Works on Honda EDC16C7 پنج‌شنبه 16 بهمن 1404 10:33
    Tried to read and write Honda Accord Bosch EDC16C7 ECU with Magic Motorsport Flex ecu programmer. Doing CONNECT shows no ID information. But read and write went fine. AutoTuner failed to ID it also. So no read process started. So FLEX failed or didn’t showed up an ID but carried out reading and writing. This is just...
  • Alientech KESS3 Adds Boot Protocol for GM E67 سه‌شنبه 14 بهمن 1404 12:29
    Problem: It’s a Seat taraco 2.0tdi 2023 model. Tried to read Bosch ECU MD1CS004 (HW80) with Autotuner . It doesn’t want to read it too high protection but I did a virtual read via obd I’m afraid to write it so it doesn’t crash. Error: Authentication error. This ECU has new protection and is not yet supported....
  • AutoTuner Solution: VAG MD1CS004 Authentication Error سه‌شنبه 14 بهمن 1404 12:28
    Alientech KESS3 released new Boot protocol for AC Delco E67- GM platforms. Expand your workshop possibilities with the new BOOT protocol dedicated to AC Delco E67 ECUs. Designed to guarantee full ECU access even in the most complex configurations, now alongside OBD communication. Read and write on AC Delco E67 in BOOT...
  • OBDSTAR G3 Read BMW MG1CS003 ISN Code Successfully سه‌شنبه 14 بهمن 1404 12:23
    The OBDSTAR X300 Classic G3 was able to take the ISN out of a BMW 320 year 2016 with MG1CS003 engine ECU. ECU: Bosch MG1CS003 SPC5777 Using G3 (with ECU license activation) and MP001 programmer on bench. Even without a valid subscription. I couldn’t read ISN code for these ECUs with CG FC200 or multi prog. But the G3...
  • FormulaFlash 1.1.0.0 Supports Toyota Gen3 Denso ECUs چهارشنبه 17 دی 1404 10:49
    FormulaFlash ECU programmer released new software version 1.1.0.0 in January 2026. FormulaFlash V1.1.0.0: UPGRADE DETAILS NEW PROTOCOLS ADDED Denso 3rd generation Toyota Auris 2019–2021 DENSO GEN3 Toyota Avalon 2018–2021 DENSO GEN3 Toyota CH-R 2019–2022 DENSO GEN3 Toyota Camry 2018–2021 DENSO GEN3 Toyota Corolla...
  • Launch X431 ECU Programmer for Replacing Mercedes DSM FBS4 چهارشنبه 17 دی 1404 10:44
    How to replace Mercedes-Benz W212 DSM A0002703452 (FBS4) with Launch X431 ECU & TCU programmer on bench? Quick search DSM, choose DSM and Bench mode. Check wiring diagram. Connect DSM FBS4 with Launch X431 ECU programmer according to the diagram. Read module information Read EEPROM data Read and save original...
  • Fix AutoTuner Software Crashed When Reading ECU دوشنبه 15 دی 1404 06:39
    Problem: Still having issues with autotuner , it stuck on reading ECU page and crashed. maybe someone been through this? Solution: Delete Autotuner, re-install software and try new USB cable.
  • Solving MMS Flex EDC17 ECU Bench Reading Issue دوشنبه 15 دی 1404 06:37
    Problem: I couldn’t read EDC17c74 with Flex programmer on bench i had read that ecu one year ago no problem. or maybe my flex box is the problem? Solution: Check if wires are not broken. It may stop working when wires were broken. EDC17 requires pin 4 in slot A as we can see in photo he have it on 2. It’s user error,...
  • Foxflash PCR2.1 Lost Connection and Boot Recovery Solution یکشنبه 14 دی 1404 10:44
    Problem: On ECU VAG Simos PCR2.1 I accidentally wrote wrong file with foxflash over bench. And now I lost communication with it. I made backup of eeprom and flash. Now I just try every method to write again flash. I tried with ktag boot mode but have acces only to eeprom. And with Fox Flash I have error REMOVE AND...
  • Resolving SilentKey Error on Ford S-Max DCM3.5 with Foxflash یکشنبه 14 دی 1404 10:42
    Problem: It’s a Ford S-Max with Delphi DCM35 ECU. MPPS, KESS and Foxflash all read ID. But they all have problem reading flash. Kess showing wrong security code. Foxflash showing error SilentKey. The car has before made stage1 by someone else its possible he protected it from reading now or its obd impossible this...
  • How to Choose the Right Power Supply for Foxflash یکشنبه 14 دی 1404 10:31
    POWERSUPPLY INFO! Since this is asked quite a lot frequently when it comes with foxflash programmer so the post here is about this power supply issue. Why? Instability or undervoltage can cause programming interruptions, corrupted reads/writes, or worse — bricking the ecu (so dont underestimate this, you dont want...
  • Foxflash MD1CS003 Peugeot 508 AdBlue Write Guide دوشنبه 8 دی 1404 10:26
    Problem: Peugeot 508 1.5 Blue hdi 96 kw with MD1CS003 ECU. Performing adblue in progress need info: Allready have benched read full backup using Foxflash programmer . File alllready modifed by tuner. Before i write I need to know do i need to reset adblue? I am not able to do it because of DTC U010E Emissions Control...
  • CG FC200 Supports VW MED9.5.10 ECU Bench Mode دوشنبه 8 دی 1404 10:24
    VW Bosch MED9.5.10 ECU read and write with CG FC200 programmer successfully. Read ExtEEPROM ok Read RxtFlash ok Write eeprom ok Write flash ok. Online checksum by FC200. Require MPC5XXX adapter for MED9 ECUs.
  • AutoTuner BMW ZF 6HP TCU OBD Read Now Available پنج‌شنبه 4 دی 1404 10:29
    Wrapping up the year with a long-awaited release! ZF 6HP TCUs, used in BMW E-Series (and Alpina) automatic gearboxes, are now supported with Normal Read (NR) via OBD using your AutoTuner Tool. Protocol status: This release is available as an Open BETA. It is immediately accessible to all users, as the protocol has...
  • Fix AutoTuner No Crank No Start on Mercedes ME9.7 پنج‌شنبه 4 دی 1404 10:27
    Problem: Tried to read and write 2006 Mercedes E-Class 350 w211 MED9.7 ECU with Autotuner programmer via OBD. I wrote the tuned file and got no crank no start. I can’t read ID or write back original now. Any help? Solution: SOLVED: unplug battery 10mins and I was able to write again. Issue- bad file. For this...
  • How to Move XirDecoder License and Use XRemover Correctly پنج‌شنبه 4 دی 1404 10:25
    Question 1: I want to transfer XirDecoder chip tuning software license to new laptop, can you reset this license? Answer 1: There’s actually a license reset button within the program. It will reset the license connection. It can also be used on a new PC. Question 2: Can XRemover correct checksums on its own? Does it...
  • XirDecoder Update: View Live ECU Tuning Modifications سه‌شنبه 2 دی 1404 10:52
    With the upcoming update, XirDecoder chip tuning software is introducing several important improvements. Previously, users would only receive a warning on the tuning page indicating that a file was not original. With the new update, after a file is uploaded on the main page, a new report screen will be available where...
  • Alientech KESS3 Update OBD Programming for Ford SID213 سه‌شنبه 2 دی 1404 10:51
    Alientech KESS3 released new OBD protocol for Continental SID213 ECU. 2.12.2025 — UPGRADE 2.74 A new KESS3 release that introduces OBD reprogramming for Continental SID213 ECUs on the latest diesel commercial vehicles and pick-ups, equipped with 2.0 EcoBlue engines (from 2022 onwards). No ECU removal Direct access via...
  • FormulaFlash 1.0.9.0 Release Adds New SIM2K and E-Series ECUs سه‌شنبه 2 دی 1404 10:48
    FormulaFlash ECU TCU programmer software released to V1.0.9.0 on Dec. 18th, 2025. READ-WRITE PROTOCOL BYD BYD TB10 R5F72531 BOSCH BOSCH M7.9.7.1-ST10F275 ST10F275 Boot mode reading EEPROM+FLASH Chang’an CHANGAN VISTEON STC-113-ST10F273 ST10F273 DEPHI LANDWIND DELPHI X7 MT62.1 SPC5643 GWM DELPHI MT95.1(MASTER) TC367...
  • Autotuner OBD VR Update for Porsche SDI10.x ECUs دوشنبه 1 دی 1404 11:13
    Get ready to tune the best of Stuttgart directly via the diagnostic port! Autotuner is thrilled to announce the release of the complete Porsche SDI10.x family on your Tool. You can now work on Porsche Macan, Cayenne, and Panamera equipped with SDI10.1, SDI10.2, SDI10.3, and SDI10.4 ECUs. Method: These protocols are...
  • Fix Foxflash No VR File for Crafter 2021 DCM6.2V دوشنبه 1 دی 1404 11:11
    Problem: VW Crafter 2021 dcm6.2v no go with foxflash . Virtual read obd2 not in database. Solution: On some models virtual file was not in database and solution on this is to upgrade or downgrade software version. Done it by ODIS Engineering software. Or read it in boot mode with other programmers.
  • Reading Dacia Duster 2021 MD1CS016 ECU With KESS3 دوشنبه 1 دی 1404 11:09
    Dacia Duster 2021. Flex cannot read, kess3 yes. Bosch MD1CS016 ECU. Read micro = 16mb.
  • AutoTuner Update Supports KTM KTKS and KTKZ ECUs پنج‌شنبه 27 آذر 1404 06:52
    You seemed to love the addition of the first KTMs to AutoTuner , so we decided not to stop there! Starting now, you can benefit from the KTM KTKS/KTKZ OBD NR protocol on your Tool. As a reminder, NR stands for " Normal Read" . This gives you access to the real content of the ECU on 14 different models from...
  • Foxflash Boot Mode Clone for Peugeot SID807EVO ECU پنج‌شنبه 27 آذر 1404 06:51
    Foxflash report today: Clone PEUGEOT PARTNER SID807EVO ECU successfully. SID807EVO Read/Write BOOT MODE Cloning ok Checksum correction by foxflash. NOTE: No need to read password for PSA SID807EVO, only read and write. If it is Ford SID807EVO, we need to read password first. Some users also reported that the PADFlash...
  • Flex Programmer Guide for Volvo DENSO MB279700 ECU پنج‌شنبه 27 آذر 1404 06:49
    Problem: It’s a Volvo XC-60 with DENSO MB279700–96xx ECU. Original ecu has been flooded with water. Have read eprom on bench no problem same as whole ecu. MMS Flex says there is no clone. How to clone this ECU with Flex programmer? Feedback and solution: It turned out that after writing full backup in to the...
  • Renault SID307 OBD Issue Fix Using Flex Boot Mode سه‌شنبه 25 آذر 1404 11:31
    Alientech KESS3 released new OBD & OBD VR protocols for Marelli MM11MPHW002 ECUs- Aprilia and Moto Guzzi motorcycles. Unlock tuning on the latest supersport and modern classic platforms from the Piaggio group with KESS3 — including the full RS and Tuono lineup and the Moto Guzzi V7 — and expand your offer across...