-
CG FC200 Boot Unlock and Read/Write for VAG MD1CS004
جمعه 22 آبان 1405 11:10
Successfully locked a Volkswagen Bosch MD1CS004 H80 TC298 locked ECU using CG FC200 programmer . In boot mode using the DME unlock adapter + new BD25 cable for FC200. The DB25 cable is a must for locked ECU. The new DB25 adds a GPT-4 wire for encrypted ECUs. The 0-ohm resistor needs to be desoldered. Unlock ok. Read...
-
AutoTuner Adds DCU102 Support for Jumper, Boxer and Ducato
جمعه 22 آبان 1405 11:08
Autotuner programmer released new OBD protocol for CITROËN, PEUGEOT & FIAT LCV- Visteon DCU102 goes live on OBD Virtual Read & Boot Normal Read! Expand your commercial van calibration capabilities on your AutoTuner Tool with dual programming support for the Visteon DCU102 ECU. Covering the iconic Citroën...
-
How to Fix Renault Master SID321 AdBlue Warning
جمعه 22 آبان 1405 11:06
Problem: After read and write Renault Master SID321 ECU with Autotuner programmer, adblue message pops up for 1 second then disappears, only happens on first ignition cycle after locking the van, did resets, EOBD clear too and battery off, have tried different solutions still the same problem, any ideas? Solution:...
-
AutoTuner Update Supports Iveco EDC17CV41 ECU by OBD
سهشنبه 19 آبان 1405 12:55
A massive software update expanding our agricultural, forestry, construction and commercial truck coverage is now live on your equipment! The Bosch EDC17CV41 (Iveco / CNH) ECU is now supported via 100% OBD Normal Read (NR) in Beta mode on your AutoTuner Tool . This release unlocks an extensive fleet powered by FPT /...
-
KESS3 Enables BENCH Tuning for Audi MG1CS163 ECUs
سهشنبه 19 آبان 1405 12:54
Alientech KESS3 released new boot unlock protocols for Bosch MG1CS163 locked ECUs- Audi, Bentley and Cupra. KESS3 expands its coverage of high-performance sports and luxury vehicles equipped with 2.5 TFSI/TSI and 6.0 W12 TwinTurbo petrol engines. The first operation requires opening and unlocking the ECU using the...
-
Dimsport Update Adds MG1CS163 H80 and MD1CS014 Support
سهشنبه 19 آبان 1405 12:50
Dimsport The Genius advanced ECU programmer expands its capabilities with new protocols and plugins for professional ECU programming! NEW DEVELOPMENTS. MORE ECU COVERAGE. MORE POSSIBILITIES! NEW HVR MODE PLUGINS Bosch MG1CS163 H80 — Bentley / VAG Bosch MD1CS014 — VAG Diesel NEW BENCH MODE PLUGIN Bosch MG1CS003 — BMW...
-
Alientech KESS3 Add Boot Unlock for VAG MD1CS014 Locked ECU
پنجشنبه 14 آبان 1405 09:43
Alientech KESS3 released new BOOT unlock and BENCH protocols for Bosch MD1CS014 "Locked" ECUs — Audi and Volkswagen. KESS3 expands its coverage of latest-generation Audi and Volkswagen diesel vehicles equipped with 3.0 V6 TDI engines, from 2021 onwards. Update highlights: Unlock protected Bosch MD1CS014 ECUs...
-
Flex Korhex Add Boot Unlock for VAG MG1CS011/ MG1CS111/ MG1CS163
پنجشنبه 14 آبان 1405 09:42
VAG Bosch MG1 TC298. More ECUs unlocked with Korhex ! With Flex 8.29.0.0, Korhex support expands to three additional VAG Group Bosch ECUs: MG1CS011 MG1CS111 MG1CS163 Already supported through VFI technology, these TC298 ECUs can now also be unlocked using Korhex, without working directly on the PCB. No PCB...
-
How to Unlock Fiat Ducato MD1CS069 with KESS3
سهشنبه 12 آبان 1405 11:18
Alientech KESS3 boot glitch unlock review: First md1cs069 unlocked and done. It’s a Bosch MD1CS069 locked ECU from a Fiat Ducato 2.2 year 2021. Unlocked ECU using Kess3 unlock module adapter. In boot glitch mode. Need to remove capacitors. Read ok. Write ok.
-
Flex SIM2K-510 ECU Unlock, Read and Write via OBD
سهشنبه 12 آبان 1405 11:16
Magic Motorsport Flex Hyundai/Kia Kefico SIM2K-510 review: FIRST TEST SIM2K-510 ECU. DONE WITH SUCCESS. TESTING THE NEW OBD PROTOCOL SIM2K-510 WORKS LIKE A CHARM. UPDATE: UNLOCK / READ / WRITE SUCCESS. Virtual read. by OBD. Read and write OK. You can read ecu on bench by obd protocol but for this need FL4.4 adapter.
-
ECUDesk 2.4.0.0 Restores ECU Files to Factory Settings
سهشنبه 12 آبان 1405 11:15
ECUDesk released a new function: RESTORE STOCK ( ECUDesk ECU chip tuning software 2.4.0.0, desktop client and Telegram Mini App). Returns an already modified file to factory values: switched-off DTCs come back on, and EGR/DPF/CAT and other feature patches are removed. Maps, coding and all other data stay untouched....
-
KESS3 Supports Bench ECU Tuning for Ford and VW SID213
پنجشنبه 7 آبان 1405 10:54
Alientech KESS3 released a new Bench protocol for Continental SID213 ECUs- Ford and Volkswagen. KESS3 expands its coverage of latest-generation Ford and Volkswagen commercial vehicles equipped with 2.0 EcoBlue engines, from 2023 onwards. The new BENCH protocol allows you to connect directly to the ECU connector...
-
FormulaFlash GPEC2A ECM Unlock Guide for 2019 Dodge RAM
پنجشنبه 7 آبان 1405 10:52
FormulaFlash user report: Dodge RAM 2019 5.7 with GPEC2A ECM. Read ECM in boot mode. Tuner unlock with Formula Flash. Use formulaflash to perform an unlock, and then program it using HP Tuners. The tuner performed the unlock patch manually for him, and he only applied the formula; however, formula flash does perform...
-
Flex with Korhex New Update for VAG MDG1 TC298 TC299 Unlock
سهشنبه 5 آبان 1405 05:24
Korhex now supports Bosch MDG1 — TC298 and TC299 ECUs boot glitch unlocking. Flex version 8.27.0.0 Now Available New Korhex Access for VAG ECUs New possibilities for VAG group MDG1 Bosch ECUs: Flex version 8.27.0.0 expands Korhex support to VAG group control units equipped with TC298 and TC299 processors. Already...
-
How to Solved OBDSTAR PSA MD1CS003 Locked ECU TPROT Issue
سهشنبه 5 آبان 1405 05:23
Good news! The Tprot issue on PSA Bosch MD1CS003 locked ECU has been resolved by OBDSTAR when unlocking these ECUs. Some customers reported issues with writing PSA Bosch MD1CS003 locked ECU with OBDSTAR DC706 / ECU Master . After writing ECU, car start three times, and then the problem doesn’t start again. OBDSTAR has...
-
Magic Motorsport Korhex MASK A-G Compatibility Guide
جمعه 1 آبان 1405 10:52
The Magic Motorsport Korhex boot glitch adapter has several different MASKs: A, B, C, D, E, F, G. Which ECUs does each of these MASKs support? Check here. A Mask: Delphi ETC3 B Mask: MG1CS032 C Mask: for feature (not available yet) D Mask: MG1CA920 E Mask: MD1CP001 F Mask: MD1CS003 G Mask: MD1CP007/ MG1CS047 What if...
-
Flex Korhex Red LED Error: Causes and Solutions
جمعه 1 آبان 1405 10:50
Problem: Tried to unlock a Mercedes MD1CP007 ECU with Flex + Korhex programmer. What concerns me is the LED status: Software shows Connected Antenna: Ready Voltage: 19 V But the RGB LED near the USB/power connector keeps flashing red continuously According to the Korhex manual, flashing red indicates an error...
-
Korhex Boot Glitch Unlock for Bosch MD1CS069 and MD1CS089
جمعه 1 آبان 1405 10:48
Korhex: New Support for Bosch MD1CS069 and MD1CS089. Flex version 8.26.0.0 is now available Unlock Bosch MD1CS069 and MD1CS089 ECUs without working on the PCB. With the latest Flex update, Korhex can now also be used on ECUs installed on commercial and industrial vehicles, accessing the TriCore TC299 processor through...
-
FormulaFlash BMW MEVD17.2.4 ECU Cloning and IMMO OFF
چهارشنبه 29 مهر 1405 10:45
Formulaflash read and write BMW MEVD17.2.4 DME ECU successfully. Read/write flash ok. Read/write eeprom ok. Clone ok. Checksum correction with FormulaFlash . Edit VIN ok. Modify ISN ok. IMMO OFF ok. Too many features were integrated into this device. Don’t need 3rd party software/tool.
-
Clone VAG DQ200 MQB Gearbox TCU Without Immo Adaptation
چهارشنبه 29 مهر 1405 10:43
Full bench clone of VAG DQ200 MQB DSG control module using FormulaFlash programmer successfully. Select DQ200 MQB gearbox TCU-Bench mode. One button reading original Micro/EEPROM data (Read All) and transferring it directly to the donor TCU — no immo adaptation needed. Read all and save. Connect a donor DQ200 MQB TCU...
-
AutoTuner Boot Mode ECU Tuning on Peugeot 208 1.6 THP
چهارشنبه 29 مهر 1405 10:42
Autotuner Peugeot 208 1.6 THP 200 Bosch MEVD17.4.2 ECU tuning review: This wasn’t an OBD-and-done job. The ECU arrived by post and required direct boot-mode access, meaning the ECU had to be opened, connected directly to the PCB and read at processor level before any work could begin. That is exactly the kind of work...
-
AutoTuner Reads Volvo EMS2.3 and EMS2.4 ECUs on Bench
پنجشنبه 23 مهر 1405 10:15
HEAVY DUTY RELEASE: TRW VOLVO EMS2.3 & EMS2.4 go live on Bench Normal Read! A major software update targeting commercial heavy transport, construction, and specialized industrial/agri machinery has landed on your equipment! TRW VOLVO EMS2.3 and EMS2.4 ECUs are now officially supported via Bench Normal Read (NR) on...
-
KESS3 BOOT Unlocks Locked Jaguar Land Rover MG1CS028
پنجشنبه 23 مهر 1405 10:13
Alientech KESS3 released new BOOT unlock protocol for Bosch MG1CS028 "Locked" ECUs- Jaguar and Land rover. KESS3 expands its coverage of latest-generation JLR vehicles equipped with Ingenium turbocharged petrol MHEV and PHEV engines, from 2021 onwards. New BOOT Unlock protocol using the dedicated KESS3...
-
Foxflash Cannot Connect to Chevrolet Delphi MT80 ECU
پنجشنبه 23 مهر 1405 10:12
Problem: I need to perform an "immo off" on a 2010 Chevrolet Aveo with a Delphi MT80 ECU. I’ve used the FoxFlash pinout, but I can’t get it to connect. Can anyone give me a hand? Here is the clue. Suggestions: 1). Increase voltage, give power supply at 14.5V. 2). Use a 120-ohm resistor between CANS. 3). In...
-
How to Create Firmware Files with ECUDesk Mini App
جمعه 17 مهر 1405 11:30
ECUDesk ECU remapping software development team is introducing a new client application — a mini-app that runs within Telegram. Now you can take your favorite app with you wherever you go; all you need is your mobile phone! It’s simple: Dear ECUDesk users! 1 accounts for 2 pcs and 1 phone!!! It’s simple: 1. Follow the...
-
Alientech KESS3 Supports Locked BMW MG1CS049 via OBD
جمعه 17 مهر 1405 11:29
Alientech KESS3 released a new OBD protocol for Bosch MG1CS049 "locked" ECUs on BMW M and Alpina. Work on some of the most sought-after high-performance BMW and Alpina models equipped with the 3.0 Bi-Turbo S58 engine, from 2021 onwards, directly via OBD with KESS3 and Powergate. BENCH Unlock required Read...
-
AutoTuner Supports Volvo Denso VEA Gen2 via Bench
جمعه 17 مهر 1405 11:27
A major technological breakthrough has landed on your AutoTuner Tool ! AutoTuner is thrilled to announce world-first, exclusive Bench mode support for the Denso VEA Gen2 (SPC5777M) ECU family ! A Look Back: In 2018, AutoTuner was the first to release support for the initial Volvo Denso ECUs (SH72546) equipping VEA...
-
Flex Korhex Unlocks Bosch MD1CS003 in Bench Mode
چهارشنبه 8 مهر 1405 09:42
Finally! Flex Korhex released new Boot Glitch unlocking solution for Stellantis Bosch MD1CS003 ECUs. Version 8.23.0.0 of Flex Out Now New Flex update , new possibilities. Now you can perform Boot Glitch operations on Stellantis Group Bosch MD1CS003 with Korhex by leveraging the EMFI — Electromagnetic Fault Injection...
-
Autotuner New Update Add MD1CP002 MD1CS001 MG1CS003 ECU
چهارشنبه 8 مهر 1405 09:39
A major workflow upgrade for BMW Group platforms has landed on your Autotuner equipment! Bosch MD1CP002, MD1CS001, and MG1CS003 ECUs (powered by the SPC5777M microcontroller) are now supported directly in Bench mode on your AutoTuner Tool, completely replacing the need for Mail-in Unlock. Supported Lineup (Bosch...
-
ECUDesk Support Ticket: How to Create One
چهارشنبه 8 مهر 1405 09:38
ECUDesk ECU remap software has a built-in technical support system. You can submit questions directly from the software, create support tickets for ECU files, and receive responses from our specialists in the MY TICKETS panel. If ECUDesk does not recognize your file, does not support a required function, or you...