iecutool

Automotive ECU Tools

iecutool

Automotive ECU Tools

عناوین یادداشت‌ها

  • Renault SID309 ECU Read Error with Xhorse Multi Prog Explained دوشنبه 24 دی 1403 11:26
    Question: Xhorse multi prog failed to read the Renault Continental ECU SID309. The error is: pflash unprotection failed — connection failed. This ECU is currently not supported by multiprog. sid307, sid309 and sid310 have Tprot password active; if you don’t find before password through obd then you can’t have access...
  • Fixing OBD Write Failure on MB Vito EDC16C2 with Foxflash دوشنبه 24 دی 1403 11:21
    Problem: Mercedes VITO, edc16c2 ECU. Foxflash read ok via OBD, OBD Write ok but car doesn’t start. Solution: It was tested to work couple times so far, but maybe checksum wasn’t done with foxflash on this case. Checksum is fucked up. If read with foxflash, power supply is important. Radiator turning on while writing....
  • FormulaFlash V1.0.1.1 Brings DCM7.1AP Bench Mode Functionality سه‌شنبه 18 دی 1403 12:46
    FormulaFlash ECU and TCU programmer released a big update on Jan. 7th, 2024. We’re excited to introduce the latest FormulaFlash update, packed with cutting-edge features for ECU programming and optimization: What’s New? • Expanded ECU Support: • MG1CA007, MG1CA811, MG1CA920, MG1CP002, MG1CP007, MG1CS001,...
  • Fixing Foxflash EDC16C3 Read/ Write Issues on Bench دوشنبه 17 دی 1403 10:14
    Problem: No possible to read and write edc16c3 PSA ECU with foxflash on bench. Any solution? Solution: Bad connection. Check the bench pinout in foxflash. You must add a ground wire for bench box because now you connect only the resistor. If still not working just remove resistor and connect directly the brown wire to...
  • VAG MED17.5 ECU IMMO OFF Tutorial Using CG FC200 دوشنبه 17 دی 1403 09:52
    CG FC200 will do VAG MED17.5 ECU IMMO OFF in device directly without 3rd party software. Check instructions below: Run FC200 software, select Bosch MED17.5 TC1766 ECU. View wiring diagram Connect MED17.5 ECU with FC200 following the diagram Identify ECU. Read and save Dflash. Then read and save Pflash. Go to ECU...
  • OBDSTAR DC706 Update V31.50: Add GM ECM IMMO OFF دوشنبه 17 دی 1403 09:48
    OBDSTAR DC706 as well as X300 Classic G3 with ECU flasher license released a big update on ECM software V31.50. Adds many new ECUs and IMMO OFF function directly in the device including GM AcDelco E83, Bosch ME7.8, ME7.8.8, M7.9.7, M7.9.7.1, MEV17.4 ECUs etc. ECM V31.50 1. Details Added: • Add ALFA ROMEO MAGNETI...
  • How to use Foxflash to read BMW EDC17CP45 چهارشنبه 5 دی 1403 12:16
    Problem: Foxflash failed to read BMW F11 Bosch EDC17CP45 ECU via OBD? Solution: Read it on bench. It is safe. BMW EDC17 none of them worked on OBD. Read obd is vr. Original file not found in database. Foxflash software does not work on obd for BMW EDC17 ECUs. zf8hp only on obd, ecu you need to do it on bench. ZF8HP...
  • How to Read Write Iveco Trakker EDC17CV41 ECU with Foxflash چهارشنبه 5 دی 1403 12:14
    FOXFLASH User feedback: Iveco trakker Edc17cv41 ECU bench + DCU boot mode ADBLUE OFF Read ok. Writing ok. Checksum by foxflash. It runs great Foxflash EDC17CV41 bench mode pinout Some ECUs enter bench mode with the pinout below Some ECUs enter bench mode with the pinout below Foxflash EDC17CV41 boot tricore pinout Use...
  • Foxflash Boot Mode for Nissan Juke EMS3155 ECU Programming چهارشنبه 5 دی 1403 12:11
    Foxflash read and write Nissan Juke 2016 with EMS3155 ECU on boot mode. Purchased a used EMS3155 ECU which I was able to read the password in boot mode. It’s possible to read the password in boot mode by various tool. Read ok, write ok, checksum by foxflash. Voltage supply 13V. DTC off. All good. Check boot mode...
  • How to Connect Xhorse Multi Prog to Xhorse App and Key Tool جمعه 30 آذر 1403 06:40
    Question: How to I combine xhorse multi prog with the Xhorse App and key tool plus? Run Multi-Prog software, go to Update Online tab- Combine device Software will bring a QR code. Scan the QR code with Xhorse App for device binding. Combine multi prog and keytool plus into your xhorse account via serial number....
  • Can Alientech KESS3 OBD Read Ford SID209 ECU? جمعه 30 آذر 1403 06:36
    Is Alientech KESS3 protocol 3000 safe on obd, Ford Ranger T6 2018 3.2 Sid 209?? Here is the clue. If it is a non smart key, yes, it is safe. Read ID first make sure the protocols are right. Ford ranger, Ford transit, Mazda bt-50, same ecu same engine. If it’s smart key just save yourself the hassle and use boot mode....
  • Nissan Navara 2021 ECU Reading with KESS3 Bench & OBD جمعه 30 آذر 1403 06:00
    Alientech KESS3 recent update brings a new Continental SID321 ECU (OBD/Bench mode). Tested on a Sid321 Nissan Navara all good. Working perfectly by OBD and bench. Did Navara 2021 in bench mode, made one file revision again on bench. Then cosutomer asked to add egr off also, couldn’t connect bench third time so did by...
  • New CG100X V1.6.6.0 Release Adds R7F7010643 Airbag Support سه‌شنبه 27 آذر 1403 05:51
    CGDI CG100X programmer released new software version V1.6.6.o on December 16th, 2024. CG100X new version V1.6.6.0 update details: 1. Added 35 airbag models. The following models are added for airbag. BAIC A00108504 R7F701A033(encrypted) BYD AUTO SA6H-3658100 R7F710643(encrypted) BYD AUTO SA3HV-3658100A...
  • BMW X3 E83 Siemens MS45 ISN Extraction Simplified with KESS3 سه‌شنبه 27 آذر 1403 05:49
    How to easily get an ISN from DME BMW? This is a BMW X3 E83 2004 with engine computer Siemens MS45. This type of MS45 computer does not need to be opened to read them and be able to adapt them to a car. Alientech KESS3 read this DME without problem. FC200 does not make siemens. Select Siemens MS45 ECU and bench mode....
  • Clone Fiat ME17.3.0 ECU Easily with CG FC200 Programmer سه‌شنبه 27 آذر 1403 05:47
    How can you clone an ME17.3.0 ECU computer from the Fiat brand using CG FC200 programmer ? These computers come on the Fiat FCA platform of the Mopard line. Run FC200 software, select Fiat, model and Bosch E17.3.0 ECU. Check the wiring diagram. FC200 gives 3 versions of pinouts. Try them one by one. In this case,...
  • Great Wall EDC16C39-6.H1 IMMO OFF Solution Guide پنج‌شنبه 22 آذر 1403 11:15
    Soultion for immo off for GREAT WALL WILGLE. ECU BOSCH 0281013328 EDC16C39–6.H1 MADE IN CHINA Great Wall EDC16C39–6.H1 IMMO OFF Tips Make immo off in eeprom only. eeprom only 95320. You can read eeprom with CG FC200 or other programmers. After writing in eeprom 95320, then jump tthe ecu PINS on the PCB as described...
  • Verified FormulaFlash Success Stories and Tool Performance پنج‌شنبه 22 آذر 1403 11:13
    FormulaFlash is a new and relatively good-priced tool and to keep an eye on updates and news regarding to tool, iecutool.eu here lists real user feedback on this tool- what succeeded and what failed. Success List: DQ381 Read/write checksum ok DQ250 read, write ok, checksum no MED9.1 read/write, checksum no Audi A4 B8...
  • FormulaFlash IMMO OFF Guide for Bosch MED17.5.21 ECU پنج‌شنبه 22 آذر 1403 11:11
    It is a VW Golf Ecu 1.4Tsi 2013 with Bosch MED17.5.21 ECU. Read/Write no problem with formulaflash. Used the Immo off Function in the FormulaFlash Software with one click. Checksum by Formula flash. It’s a good tool for bench work only at the moment really. Read and write times are ok. Has good support for Bosch ECUs.
  • PCM Cloning Guide for 2016 Jeep Grand Cherokee with GPEC2 سه‌شنبه 20 آذر 1403 06:12
    2016 Jeep Grand Cherokee PCM cloning successfully done with OBDSTAR DC706 . PCM type: Jeep Continental GPEC2 MPC5566+95320 Device used: OBDSTAR DC706+ P003 adapter or MP001 Do it in boot mode. Need to use extra power supply. Read EXT eeprom and Read INT flash of the original PCM. Backup both eeprom and flash of the...
  • Foxflash Successfully Reads and Writes VW T5 EDC17CP20 in Boot Mode سه‌شنبه 20 آذر 1403 06:10
    This is a VW T5 Transporter with Bosch EDC17CP20 ECU. It has high tprot. often seen high tprot case. OBD cannot read password, no bench password is available either with foxflash programmer . Bench mode failed, error bench mode not supported, used Boot modoe tricore. Lastly got password via boot password, so after...
  • New KESS3 Update Enables SID321 ECU Read and Write Options سه‌شنبه 20 آذر 1403 06:07
    This latest Alientech KESS3 development enables you to read and write Continental Vitesco SID321 ECUs, either via OBD or directly from the ECU connector pins. With this option, you can also back up the data or bypass the gateway if needed. This latest KESS3 development enables you to read and write first and second...
  • Foxflash V1.4.2 Firmware D087 Enhances CAN and Kline Speeds جمعه 16 آذر 1403 06:12
    Foxflash released a new firmware version: D087 on Nov. 28th, 2024. Foxflash Update : V1.4.2 Software Firmware Version FW: D087 Update Info (11/28/2024): 1. Update firmware response speed 2. Rewrite CAN and Kline working speed to improve reading and writing speed
  • BMW MSD80 VIN and ISN Modification Success with FormulaFlash جمعه 16 آذر 1403 06:10
    Formulaflash programmer new user feedback from Whatsapp group: modify VIN and ISN on a BMW MSD80 DME successfully. CAR: BMW ECU: MSD80 VIN: READ/MODIFY OK. ISN: READ/MODIFY OK. FormulaFlash allows you to modify ISN, VIN, and even perform Immo Off with a single click (hit VIN/ISN/IMMO OFF function), saving time and...
  • Foxflash OBD Guide for Renault Megane EMS3150 ECU Read/ Write جمعه 16 آذر 1403 06:09
    Tips to read and write Renault Continental EMS3150 ECU with Foxflash . It is a Renault Megane 1.2 TCe with Continental EMS 3150 ECU. Read via OBD. Write via OBD. Checksum by foxflash. CONDITIONS: ENGINE TEMP MUST BE BELOW 50° C. DRIVER DOOR OPEN, CAR WAS IN 1ST GEAR, TURN ON HAZARD WARNING SWITCH, ON 50% R/W PRESS...
  • FormulaFlash Bosch ME7.8.8 One-click IMMO OFF سه‌شنبه 13 آذر 1403 09:59
    There are several tools to do IMMO OFF for Bosch ME7.8.8 ECU. MDFALSHER with protocols 113 and 49. or S&V with ME788 protocol (protocol takes $500) But they do not work on some Chinse brands, Geely, Roewe, FAW Bestune etc. FormulaFlash ecu programmer now supports one-click IMMO OFF for ME7.8.8 ECU. FormulaFlash...
  • OBDSTAR DC706 Error 11 on GM GEN3 BCM with Secure MCU دوشنبه 12 آذر 1403 11:21
    Problem: OBDSTAR DC706 Failed to read 2022 Chevrolet Camaro BCM module 70F3558+ 24C32, it gave error code 11. Tested it on a 19 Chevy Colorado the other day, was not possible to read it either. Any idea? Solution: These are GEN3 BCMs with 5bsk and secure MCU , obdstar won’t do it. Not supported yet. IO Terminal won’t...
  • New KESS3 Powergate Update for Toyota/ Lexus/ Jeep/ Dodge دوشنبه 12 آذر 1403 11:19
    Alientech released new upgrade for KESS3 and Powergate. Open new horizons for your workshop with the latest protocols for Toyota, Lexus, Dodge, and Jeep — perfect for those passionate about SUVs and off-road vehicles! With KESS3, you can remap the Denso Gen IV R7F702002 V35A-FTS ECUs for the newest Toyota and Lexus...
  • FormulaFlash Bench Mode Read for BMW 5 Series MSD85 ISN چهارشنبه 7 آذر 1403 10:49
    FormulaFlash read 2016 BMW 5 series MSD85 ISN from a 2016 BMW 5 series successfully. Run FormulaFlash software, select BMW- 5 series- 2003–2016- MSD85 ECU Select Bench Mode. Formulaflash also reads MSD85 in boot mode. Check wiring diagram and connect MSD85 with formula flash following the wiring diagram. Connect ECU...
  • FormulaFlash Triumphs Over KT200II in VW MD1CP004 ECU Test چهارشنبه 7 آذر 1403 10:47
    Iecutool.eu share one of our customers working experience on FormulaFlash programmer: "Friend of my trying to read a VW Bosch MD1cp004 ECU with KT200II did not work how mutch he try and helpless. And i send FormulaFlash to him because I am waiting for more updates. He test read same ECU and read was no problem...
  • Easy GM E80 ECM Cloning Using Launch X431 Programmer چهارشنبه 7 آذر 1403 10:44
    Cloned GM ACDelco E80 ECM using Launch X431 ECU & TCU programmer successfully. Quick search "E80" and select model/year. For example, its an E80 out of a Buick Cascada 2016. Check bench wiring diagram Connect Launch X431 ECU programmer with E80 ECM following the wiring diagram Connect ECM and read FLASH...