iecutool

Real OBD Read for Ford EMS251X ECUs via AutoTuner

NEW AUTOTUNER PROTOCOL UPDATE!
We are updating our OBD protocol for Continental EMS2510, EMS2511, EMS2512 and EMS2513 ECUs installed in Ford vehicles.
Until now, only virtual reading (VR) was available for these ECUs. This operation has now been replaced with a real reading (NR) directly via the OBD port.

This ensures full compatibility, without depending on the availability of the file on our server.

Important note: previous virtual reads were 4MB in size, while the new real reads are 3MB. A new read is therefore required before any further operation on these ECUs.

Key Features of This Release:
Type: Engine Contol Unit (ECU).
Readout: OBD NR.
MCU: TC1791.
Read time: 3min.
Write time: 1min 30sec.
Checksum correction by autotuner.

AutoTuner

iecutool چهارشنبه 25 تیر 1404 ساعت 12:49

0 نظر

How to Fix Foxflash Write Issue on EDC17C60 ECU

Problem:

Has anyone already unlocked the password on esc17c60? I extracted the password with foxflash but I can’t find the procedure to rewrite it. I used bench but error password. I can read flash and eeprom in boot mode but not rewrite and not start.

Foxflash Failed to Write PSA EDC17C60 ECU After Retrieve Password

Solution:

If you put it in a folder foxflash will automatically find it.

Save the extracted password in the same folder as new file the write new file.

Usually, we can read this ecu easily on bench without password. But if the ECU is updated or replaced in the dealership, you may need to do it in boot.

Foxflash ECU Programmer

iecutool چهارشنبه 25 تیر 1404 ساعت 12:47

0 نظر

KESS3 Adds Denso TFW6A-E TCU Bench Protocols for Mazda

New Alientech KESS3 BENCH protocols for Mazda SkyActiv ECUs and TCUs.

UPGRADE 2.31

Exclusively with KESS3, you can operate in BENCH mode — including cloning — on the Denso TFW6A-E TCU, installed on Mazda vehicles with 2.0 SkyActiv-G and 2.2 SkyActiv-D engines, produced since 2017. An effective solution for advanced repairs, especially in case of faults or replacement of the automatic gearbox, even on recent models already common in workshops.

You can also access Mitsubishi HF01 ECUs for work on 2.0 SkyActiv-X engines, in production since 2019. Read and write safely on the bench: carry out targeted modifications without risking ECU damage.

With this update you can:

Customize key transmission parameters and effectively clone Denso TCUs, simplifying any reprogramming task.
Optimize ECU and TCU synchronization to achieve a smoother and more efficient dynamic response.

Supported ECUs and engines with this update:

Denso TFW6A-E — 2.0 SkyActiv-G and 2.2 SkyActiv-D
Mitsubishi HF01–2.0 SkyActiv-X

KESS3 Adds Bench Protocols for Mazda SkyActiv ECUs and TCUs

Alientech KESS3

iecutool جمعه 20 تیر 1404 ساعت 12:43

0 نظر

XirDecoder Offers Full Tuning from Stage 1 to 3

XirDecoder is a professional software platform that offers the most advanced chip tuning solutions in the automotive world. With its rich database containing more than 130,000 files, it offers a unique experience in vehicle optimization. It offers professional solutions for all your chip tuning needs, from Stage 1 to Stage 3, from DPF/EGR/Adblue deactivation to Launch Control. Our system is designed to meet all software optimization needs of modern vehicles.

Here we will show how easy it is to perform modifications and solutions using hardware and XirDecoder software.

Takes Foxflash and BMW Bosch EDC17C50 ECU as an example.

Function: EDC17C50 Hardcut, EGR, DPF, Stage 1

Same procedure goes to other programmers, Flex, Autotuner, FC200 etc.

Step 1: Read the ECU

Read this ECU with foxflash in bench mode. Save data.

XirDecoder Chip Tuning Software with 130K+ Files

Step 2: Perform Hardcut Solution

If don’t need to perform Hardcut or DTC off solution, skip to Step 3.
Run XirDecoder software.
Select Hardcut function.

Select vehicle brand and ECU.

Upload original data read by Foxflash.

EDC17C50 available 5700 RPM. The XirDecoder allows cut fuelling at a set RPM (normally 4300 rpm) making the revs bounce off the limiter!
Select 4000RPM and Download.
Save file.

Software does not do checksum correction. It’s hardware’s job.

Step 3: Perform Other Solutions
Select ECU EDC17C50.
Upload data
Then select the functions you need.
For example, XirDecoder software allows to perform EGR OFF, DPF OFF, Vmax OFF and Stage 1 for this ECU.
Then hit Download.