iecutool

Automotive ECU Tools

iecutool

Automotive ECU Tools

عناوین یادداشت‌ها

  • How to Read Suzuki BCM D70F3584 via Xhorse Multi-Prog پنج‌شنبه 30 مرداد 1404 11:24
    It’s a Maruti Suzuki Brezza with BCM processor D70F3584. Xhorse Multi Prog reads and writes the BCM successfully. Need to disassemeble the BCM module. In multiprog software, select MCU- Renesas V850- D70F3584 and check wiring diagram. Connect Multi prog with BCM according to the wiring. Read chip ID. Read Dflash...
  • Best Tools to Read Write FAW Weichai SID605 ECU پنج‌شنبه 23 مرداد 1404 06:26
    What tool to read Chinese FAW WEICHAI Continental SID605 ECU? Here is the clue. Alientech KESS3 : Why Suitable: A versatile tool supporting OBD, bench, and boot modes, KESS3 is compatible with Siemens/Continental ECUs, including SID605, for FAW and Howo vehicles. It offers comprehensive reading and writing...
  • New XirDecoder DTC OFF Support for DCM3.x and MED17 ECUs پنج‌شنبه 23 مرداد 1404 06:23
    XirDecoder ECU Chip Tuning Software adds more DTC OFF ECUs in Aug. 2025. Adds: 1). FREE DTC Solutions for Ford DCM3.5 ECU! Available now for all users — including DPF, Lambda, EGR, and TVA OFF functions. 2) Add DTC Solutions for Ferrari MED17.3.5 ECU Ferrari owners and workshops can now enjoy full fault code...
  • Foxflash VR Read Write for VW Polo GTI 1.8TSI Simos 18.1 پنج‌شنبه 23 مرداد 1404 06:20
    Here comes the new user feedback from one of the Foxflash users: VW Polo GTI 2017 1.8TSI 192HP Simos 18.1 ECU. OBD VR read ok. Hit "Read" and get vr file online. OBD Write ok. Checksum correction with foxflash. Simos 18.1 VR reading need luck. There is no support for Golf 7 gti engine. golf mk7 vr was no...
  • How to Solve Foxflash Read Fail on Ford SID211 جمعه 17 مرداد 1404 07:14
    Problem: It’s a Ford Transit Custom 2017 with SID211 ECU, Foxflsah reads id ok but reading error. Any idea? Solution: Charge maintenance at 14V+. Read and clear all defaults in your ecu and try. If not good repeat this and remove the positive connector on your battery for 5min and try again. Normally reading is good....
  • How to Read Write Fiat MJD 9DF ECU via Foxflash جمعه 17 مرداد 1404 07:11
    Foxflash new user feedback today: Fiat Marelli MJD 9DF ECU. Tired obd2 didn’t work Did it via bdm and it was quite easy . Read 20–25 minutes. Write 20–25 minutes. Checksum correction via foxflash Bit of work but very smooth. lots of heat, lots of patience. Foxflash usually does MJD 9DF full read and write via OBD, if...
  • ECU Tuning Software Review: XRemover vs XIRDecoder جمعه 17 مرداد 1404 07:09
    XRemover vs. XIR Decoder: Subscription-Based ECU Tuning Software Comparison. In the world of ECU tuning, two software tools stand out for their automation and versatility: "XRemover" and "XIR Decoder". While both cater to similar needs, they differ in pricing structure, support levels, and daily...
  • FormulaFlash Update: SIM2K SID208 SID209 Support دوشنبه 13 مرداد 1404 12:16
    FormulaFlash ECU and TCU programmer released new ECU protocols on Aug. 5th, 2025. THE NEWLY ADDED PROTOCOL IS AS FOLLOWS Continental Series SIM2K-341 (ECM) MPC561 reads and writes flash and maps via BENCH; SIM2K-141 (ECM) MPC561/2 reads and writes flash and maps via BENCH; SIM2K-141 (TCM) AM29F400BB reads and writes...
  • Best Tool to Clone Renault DC4 Gen1 TCU: X-prog3 or Foxflash دوشنبه 13 مرداد 1404 12:13
    Renault Continental DC4 Gen1 gearbox TCU cloning review: Renault Clio 1.2 88KW 2014 Gearbox Cloning. Gearbox type: Continental DC4 Gen1 Foxflash : Read ok on bench. Write failed. This specific version is encrypted and cannot be cloned with Foxflash. Also Foxflash Reads and Writes only Maps on Flash, no Eeprom! Launch...
  • FC200 or FormulaFlash Which ECU Tool Is Better دوشنبه 13 مرداد 1404 12:09
    Question: I wanna purchase a second programmer and I’m confused between FormulaFlash and CG fc200, which is better? Here are some users’ reviews to help you make a better decision. 1). I have Foxflash also and recently bought Formula. In my opinion, Formula is an updated next generation device compared to FC200 ....
  • AutoTuner Update for GPEC4LM ECU BOOT and OBD Beta جمعه 3 مرداد 1404 09:46
    NEW AUTOTUNER PROTOCOL UPDATE! A new update is available for the Continental GPEC4LM ECU in BOOT mode , found in Alfa Romeo, Fiat and Jeep vehicles. This update adds support for a specific variant of this ECU, notably found on 1.5 engines. For those who followed the previous update, you may have already noticed these...
  • KESS3 Update: Add OBD and Bench Protocols for GM ACDelco TCU جمعه 3 مرداد 1404 09:43
    Alientech KESS3 released new TCU protocols- Cadillac, Chevrolet, GMC. Boost your business with the latest protocols for ACDelco and Bosch TCUs. Work in OBD and BENCH mode — no need to open the unit! Read and write on ACDelco T87 and T87A, and Bosch T93 Support for pickups, SUVs, and muscle cars from 2015+ Customize...
  • Free DPF GPF EGR Adblue by FormulaFlash Platform جمعه 3 مرداد 1404 09:40
    Good news! FormulaFlash programmer free ECU Functions — now available! We are excited to offer FREE processing for essential ECU functions directly through our platform. Take full advantage of this powerful tool to optimize your vehicle’s performance and reliability without any cost! Available Free Functions: • DPF...
  • BMW EDC16C35 Stage 1 Remap with PADFlash and XIRdecoder پنج‌شنبه 2 مرداد 1404 11:18
    Here iecutool.eu demonstrates a Stage 1 remap on BMW using Padflash tool and XIRdecoder software . With the right software and tools, remapping has never been so easy. EDC16C35 BMW ECU read and write with Padflash tool. Automatic file tuning with XIRdecoder software. Step 1: Read the ECU with PADFlash Select Bench...
  • Solution for Foxflash Login But No Program Launch پنج‌شنبه 2 مرداد 1404 11:16
    Problem: Failed to run Foxflash software after login? How to fix program not starting after this screen? It’s Windows 10 system. Solution: Make sure foxflash is plugged in and showing as dfb in Device Manager. Kill the app through task manager. Unplug FoxFlash USB. Open FoxFlash manager. Click Activate. After the...
  • FormulaFlash July Update Adds Simos IMMO Functions پنج‌شنبه 2 مرداد 1404 11:13
    FormulaFlash programmer released new software upgrade on July 16th, 2025. This update significantly expands compatibility with immobilizer (immo) data cloning, FLASH/EEPROM read/write, and checksum correction across multiple brands and ECU types. Update Content Volkswagen Audi Porsche Added SIMOS12.X / SIMOS8.3X /...
  • Foxflash V1.4.3.1 Asks for Activation After Update پنج‌شنبه 26 تیر 1404 06:29
    Problem: I have foxflash manager version 1.4.1 when instart it it says newer update is available 1.4.3.1. After update, it asks to contact the vendor to activate. Do I need to activate it again? Solution: Yes, in this case, you need to contact us to activate Foxflash. Send the device serial number and register email...
  • How to Solve Foxflash Email Registration Code Issue پنج‌شنبه 26 تیر 1404 06:27
    Problem: I bought the Foxflash equipment. It arrived yesterday. I put in my email and the phone number but the device says i already have a registered email. Error: "Another email is already registered with the code. Register with the correct email." Solution: You bought it secondhand and YOU MUST USE...
  • New Bench Update for Simos 8.3 ECU by AutoTuner پنج‌شنبه 26 تیر 1404 06:26
    NEW AUTOTUNER RELEASE. We are thrilled to announce that the Continental Simos8.3 ECU is now supported in BENCH mode. Commonly found in Audi and Volkswagen vehicles equipped with the potent 3.0 TFSI V6 Supercharged engine. This remarkable engine, with its sophisticated direct injection and robust internal components,...
  • Fix Foxflash Read Issue on SID803 ECU Bench Mode چهارشنبه 25 تیر 1404 12:51
    Problem: Tried to read Peugeot SID803 ECU with foxflash on bench. I can read jusd id. But not more. Any solution? Solution: Bench only sid803a while sid803 boot or bdm SID803A obd/bench (check pinout ) SID803 boot important sid803 maps in mpc not in flash. SID803 boot pin to foxflash Connect multifunction cable as...
  • Real OBD Read for Ford EMS251X ECUs via AutoTuner چهارشنبه 25 تیر 1404 12:49
    NEW AUTOTUNER PROTOCOL UPDATE! We are updating our OBD protocol for Continental EMS2510, EMS2511, EMS2512 and EMS2513 ECUs installed in Ford vehicles. Until now, only virtual reading (VR) was available for these ECUs. This operation has now been replaced with a real reading (NR) directly via the OBD port. This ensures...
  • How to Fix Foxflash Write Issue on EDC17C60 ECU چهارشنبه 25 تیر 1404 12:47
    Problem: Has anyone already unlocked the password on esc17c60? I extracted the password with foxflash but I can’t find the procedure to rewrite it. I used bench but error password. I can read flash and eeprom in boot mode but not rewrite and not start. Solution: If you put it in a folder foxflash will automatically...
  • KESS3 Adds Denso TFW6A-E TCU Bench Protocols for Mazda جمعه 20 تیر 1404 12:43
    New Alientech KESS3 BENCH protocols for Mazda SkyActiv ECUs and TCUs. UPGRADE 2.31 Exclusively with KESS3, you can operate in BENCH mode — including cloning — on the Denso TFW6A-E TCU, installed on Mazda vehicles with 2.0 SkyActiv-G and 2.2 SkyActiv-D engines, produced since 2017 . An effective solution for advanced...
  • XirDecoder Offers Full Tuning from Stage 1 to 3 جمعه 20 تیر 1404 12:41
    XirDecoder is a professional software platform that offers the most advanced chip tuning solutions in the automotive world. With its rich database containing more than 130,000 files, it offers a unique experience in vehicle optimization. It offers professional solutions for all your chip tuning needs, from Stage 1 to...
  • Foxflash Supports Ford SID807EVO ECU in Boot Mode جمعه 20 تیر 1404 12:38
    Foxflash new user report: Ford cmax 2015 1.6 tdci 115 SID807EVO ECU Read/write/checksum and get password with foxflash . Boot mode. This can be done obd also with the full can protocol. Tested it and works fine on Fords. Unlike Peugeot/Citroen you can only do boot. Check SID807EVO boot mode pinout to foxflash here...
  • How to Find Wiring Diagrams in PADFlash جمعه 6 تیر 1404 10:28
    Problem: PADFlash software starts fine, but cannot see the manual and wiring diagram. Any idea? Solution: Manuals are in the Updater. How to Check Wiring Diagram? Run PADFlash Updater tool. Press Search function. Enter ECU and Search. You will see instruction and wiring diagram pinouts.
  • Use DC706 for Fiat ME7.9.10 ECU IMMO OFF جمعه 6 تیر 1404 09:47
    OBDSTAR DC706 read and write Fiat ME7.9.10 ECU on bench successfully. bench ( k-line) with P004 adapter. Read write flash ok. Read write eeprom ok. int flash checksum correction by DC706. Immo off in device. No need 3rd party tool or software.
  • How to Read Opel EDC17C19 ECU Using Foxflash Tool جمعه 6 تیر 1404 07:17
    Foxflash will read and write Opel Insignia 2.0cdti Bosch EDC17C19 ECU in both bench and boot mode. Bench mode To read and write use the following driver: → BENCH TRICORE → OPEL → TC1796 — OPEL → EDC17 C19 bench pinout to EDC17 C19 If cannot read ecu on bench mode, try boot mode. Boot mode Connect with the...
  • FormulaFlash New version: Free ECU Data Cloud Processing جمعه 23 خرداد 1404 10:39
    Formulaflash ECU data cloud processing platform is officially launched and Beta version is available (DTC/DPF/GPF/OPF/EGR/EVAP/AdBlue are free and available to all users in the beta version. By ticket system, engineers will manually process the data for you for free). All data processing is handled manually by...
  • How to Solve Dacia MD1CS006 No Start Issue جمعه 23 خرداد 1404 10:35
    Problem: MD1CS006 dacia sandero 2 adblue off. Foxflash read and write no problem on bench mode. Checksum by foxflash, but car won’t start. Any solution? Solution: That’s an MD1 ECU, you reset on original and disconnect adblue module. You can sort it, just reset and disconnect adblue module . Also remember even if...